NBS Source
I'm a manufacturer

weberfloor smooth 4150

Verified by manufacturer 5 months ago

Saint-Gobain Weber Third party certifications:
  • EPD

    EPD

    Certificate type

Self-smoothing thin topping screed suitable for residential and commercial areas

Jump to:
BIM object icon
+44 (0)1525 718877 Website

Application

Prepare:


The surface strength of the substrate must be greater than 1N/mm²

It is essential the substrate is suitably prepared and primed with weberfloor 4716 primer prior to installing the Weber floor screed.

The substrate should be clean, free from dust, grease and other impurities that might prevent adhesion.

Walls and any upstands (pillars, columns etc) should be isolated with 10 x 100mm foam.

Large irregularities in the substrate (>30m) should be filled in with an application of weberfloor base rapid 4360, this should be allowed to harden and then primed before application of weberfloor smooth 4150 can begin.

Holes and leaks in the substrate should be sealed. The substrate should be vacuum cleaned, prepared and primed with weberfloor 4716 primer according to the instructions on the data sheet.

Priming improves the screed’s adhesion to the substrate and prevents the formation of air bubbles and dewatering of the screed. Priming also improves the flow properties of the screed. Dry and very porous substrates (cast-in-situ concrete floors) may need to be treated twice. If the screed is applied in more than one layer, each layer must be primed.


Mix:


weberfloor smooth 4150 is mixed with clean water using an automatic screed mixer approved by Weber.

The material is mixed with 20% water, which corresponds to 5.0 litres per 25kg bag. It is important to add only the specified amount of water as excess water will reduce strength, increase shrinkage and encourage segregation. Whilst mixing, the water content should be checked continuously by the flow ring test to ensure that the material is correctly mixed and free from separation and lumps of powder. The flow rate should be between 240-255mm. Conversely, reduced water content increases viscosity. The temperature of the mix should ideally be between +15°C and +20°C.

For manual mixing thoroughly mix using a slow speed electric mixer (500 rpm) for at least two minutes. Allow to stand for 2 minutes.


Apply:


Light ventilation in the working area is necessary but windows and door openings must be closed sufficiently to avoid draughts during and for 3 days after application.

During application, and for at least 1 week afterwards, the substrate and ambient temperature should not fall below +10°C or rise above +25°C. The relative humidity of the substrate must be <95%.

To achieve the best finish, the floor area should be divided into bays of 6 to 8 metres depending on pump capacity and application thickness. weberfloor 4965 barrier foam should be used to form bays and stop ends. Pumping is carried out in sections so that a new section is pumped as quickly as possible and to maintain a wet edge. A wide serrated spatula or spike roller should be used to assist the self-levelling process.

Overlay

weberfloor smooth 4150 is compatible with most common floor finishes and adhesives.

It should not be painted or used without a floor finish.

Covering Time

The smoothing compound can receive foot traffic after a drying

Description

weberfloor smooth 4150 is a self-smoothing flooring compound — commonly referred to as a self levelling compound or self levelling screed — which can be applied to depths of 2-30mm and used for levelling:

  • Concrete
  • Sand/cement screeds
  • Anhydrite screeds
  • Can also be used as a levelling compound for any of our weberfloor base or renovation screeds


weberfloor smooth 4150 self-smoothing flooring compound is suitable for covering with:

  • Vinyl/linoleum
  • Carpet
  • Laminate flooring
  • Parquet flooring*
  • Tiles


Suitable for use in residential and commercial areas, light foot traffic is possible after 2-4 hours in normal conditions and the final floor covering can be installed in as little as 3 days, depending on layer thickness and site conditions.


* May require extended time before covering


Features & benefits:


  • For application depths between 2-30mm
  • Weber Low Dust TechnologyTM improves comfort of applicators
  • Pump or hand applied
  • Foot traffic after 2-4 hours
  • Floor covering can be installed in as little as 3 days, depending on layer thickness and site conditions
  • Excellent spreading and smoothing characteristics
  • Low alkalinity
  • Casein-free
  • Low emissions


Things to consider:


  • Cannot be used on external projects
  • Not to be left without a suitable floor covering
  • Not to be used where some movement is expected (eg. underfloor heating), for these substrates the floor should be levelled with weberfloor fibre 4310 or weberfloor fibre rapid 4320
  • When stored unopened in a cool, dry place at temperatures above 5°C, shelf life is 12 months from date of manufacture
  • Please refer to relevant building regulations prior to the installation of weberfloor products


General information

Finish

Smooth

Uniclass

Pr_35_31_06_78 Self-smoothing levelling screed mixesPrimary
Ss_30_42_15_10 Bonded or partially bonded cementitious levelling screed systems

CAWS

M10/19 Proprietary screeds to BS EN 13813

M10/195 Proprietary screeds to BS EN 13813

Specification data - Self-smoothing levelling screed mixes

Levelling

Applied to depths of 2-30 mm in concrete, sand, cement creeds, anhydrite screeds, can also be used as a levelling compound for any base or renovation screeds.

Application temperature

+10°C to +25°C.

Substrate

1 N/mm².

WaterUsed

5 litres/ 25kg (20%).

CompressiveStrength

C 25.

Flexural strength

F 6.

Shrinkage

< 0.05% (28 days).

Flowrate

240–255 mm.

Material:

Consumption: 1.7kg/ m²/ mm.

Pot life

20 min (after adding water).

Wear resistance

RWFC 450.

Thickness range

2–30 mm.

Setting time

Hardening Time Before Foot Traffic: 2-4 hours in normal conditions. Hardening Time Before Final Covering: 3+ days dependent on thickness and site conditions.

Product Reference

weberfloor smooth 4150

Sustainability data

BIM objects

BIM object icon

NBS BIM Object Standard

This BIM object has been authored to meet the requirements of the NBS BIM Object Standard.

Find out more about the NBS BIM Object Standard.

Platform Compatible Version
Revit
-

1

IFC
-

1

Third party certifications

EPD

EPD

EPD Certificate (weberfloor standard floor screeds)

Similar products from Saint-Gobain Weber

weberfloor acoustic system

weberfloor acoustic system

weberfloor acoustic system (Robust Detail E-FC-9)

weberfloor acoustic system (Robust Detail E-FC-9)

weberfloor acoustic system (Robust Details)

weberfloor acoustic system (Robust Details)

weberfloor base rapid 4360

weberfloor base rapid 4360

weberfloor bonded system

weberfloor bonded system

weberfloor fibre 4310

weberfloor fibre 4310

weberfloor fibre rapid 4320

weberfloor fibre rapid 4320

weberfloor industry pro top 4610

weberfloor industry pro top 4610

weberfloor industry rapid 4655

weberfloor industry rapid 4655

weberfloor level

weberfloor level