Select regional version:
The object content is configured for use in UK, but it may also be suitable for use in other locations.
| IfcExportAs |
|
IfcCoveringType |
| IfcExportType |
|
CLADDING |
| BeadsAndTrims |
|
n/a |
| BoardsFixings |
|
n/a |
| BoardsMaterial |
|
n/a |
| ContainsRedListMaterials |
|
n/a |
| CountryOfMaterialOrigin |
|
n/a |
| CountryOfProductManufacture |
|
n/a |
| EmbodiedCarbon |
|
n/a |
| Execution |
|
Install system as per manufacturerșs instructions |
| FireBarriersAndStopsFixings |
|
n/a |
| FireBarriersAndStopsMaterial |
|
n/a |
| InsulationAdditionalMechanicalFixings |
|
SPIT ISO Range,T-FIX-8M Range,T-FIX-8S Range |
| InsulationAdhesive |
|
WBS Insulation Bedding Adhesive (minimum 40%) |
| InsulationMaterial |
|
Stone Wool Insulation |
| MovementJointsAccessories |
|
n/a |
| MovementJointsFormWith |
|
WBS Powder Coated Galvanised Steel Movement Joint Bead,WBS Powder Coated Galvanised Steel Stop Bead |
| MovementJointsSealant |
|
Compriband sealing tape installed between the insulation boards |
| Preparation |
|
Remove any loose material and existing render, where required dub out the surface level, ready to receive the EWI system. The existing walls are to be cleaned with a wire brush or pressure jet wash, to the satisfaction of the Contract Administrator, to remove any friable material, algae or lichen, and to provide a good key for Wetherby products. Treat areas of moss, algae and mould growth with WBS Biocidal Wash. Dense smooth surfaces may require treating with WBS Stabilising Solution / Bonding Agent to ensure adequate adhesion on wet fix or render only applications. If the walls include existing render or the substrate isnșt line and level and requires dubbing out, the fixing lengths stated within this specification may need to change. This will need to be confirmed on site prior to the installation of the Wetherby system. Sizing of flashings, trims and beads may also require alterations. Where necessary dub out, using Wetherby Dubbing Render, any hollow / defective areas to leave a suitable surface for the application of the insulation boards. Maximum dubbing coat thickness: 16mm. Where required, apply one coat of Wetherby Biocidal Wash to the entire surface by roller or knapsack spray and allow to dry. Brush the surface to remove all signs of growth before rendering commences. Where required, apply one coat of Wetherby Stabilising Solution to the entire surface by roller, ensuring uniform coverage and allow to dry |
| ProtectiveCoating |
|
Please see Wetherby Through Coloured Render and Spar Dash Systems document for further information |
| Recyclability |
|
n/a |
| RecycledContent |
|
n/a |
| RenderApplication |
|
n/a |
| RenderCarrierOrReinforcementFixings |
|
TID-MR Range,DHM Range |
| RenderCarrierOrReinforcementMaterial |
|
Glass fibre reinforcement mesh incorporated into scrim adhesive |
| RenderCarrierOrReinforcementMeshSize |
|
50 m² Roll |
| RenderColour |
|
n/a |
| RenderDecorativeFinish |
|
WBS Mineral Aggregate Spar Dash |
| RenderMaterial |
|
WBS Polymer Cement Dashing Mortar |
| SamplesRequired |
|
Submit samples of Wetherby Dash Finish for approval. Keep approved samples on site for the duration of the contract for inspection and comparison purposes. The manufacturer offers a product sample service, providing a small sample of the finished build-up, colour and texture before a final decision is made. Contact the manufacturer for further information |
| SupportRailsAndBracketsFixingMethodBracketFixings |
|
WBS HIT 6/5 Hammerscrew Bead Fixing |
| SupportRailsAndBracketsFixingMethodMaterial |
|
WBS Powder Coated Galvanised Steel Bellcast Bead |
| SystemAccessories |
|
WBS Sealing Tape: Pre-compressed, expanding waterproof sealing tape,WBS Firtree Fixings,WBS Jointing Pieces,WBS End Caps,WBS EVO-STIK Silicone Sealant |
| SystemCompletion |
|
Inspection of completed installation,Documentation for insulated render systems,OandM manuals and data sheets relevant to the system installed |
| SystemPerformance |
|
Thermal Performance,Strength and Stability,System Tested to BS EN 13501-1:2018,Risk of Condensation,Durability,Further Information |
IFC
Revit